About

 

 

We have unearthed the article about Installing A Bathtub below on the net and think it made perfect sense to write about it with you on this page.

Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the project can move quickly; if you have to open up a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have already bought a new bathtub and also do not require to transform the setup of your previous water system pipelines.
Your devices as well as product checklist ought to make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be quite problematic due to the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular faucet ports. The former type should be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Installing the Bath tub

Utilizing the two wood boards under its feet, place the bath tub in the needed position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bathtub up until the level checks out degree.
To install faucets, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet and also the normal outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub must wait until the tub has actually been made use of at least when as this will certainly settle it into its last placement.

 

 

Preparing for the Installation

First of all, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to prevent stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.

 

 

Tiling Around the Tub

In the area where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, triggering the water to pass through the wall surface between the bath and the tiling, leading to problems with moisture as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components and also installations. They are offered in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack fairly early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed our topic about Tools You Need to Install a New Bathtub . Thanks so much for taking time to read our piece of content. Liked our write-up? Please share it. Let other people check it out. Thanks for going through it.

Book Services